HEARTH PRODUCTS
KITS AND ACCESSORIES
REFLECTIONS REMOTE CONTROL
REPLACEMENT KIT
P/N 750,251M
REV. A 01/2008
INSTALLATION INSTRUCTIONS FOR THE REFLECTIONS REMOTE CONTROL
REPLACEMENT KIT (KIT NUMBERS: H1454 AND H6977)
Step 5. Remove the grate.
GENERAL INFORMATION
Step 6. Remove the ember bed.
Step 7. Remove the fireplace floor.
This Remote Control Replacement Kit is to be used to replace the
ReflectionsElectricFireplace’sRemoteControl. Thekitcomponentsare
shown below.
Step8. RemovetheDVDplayer. Makesuretolabel the“VideoOut” and
“Sound Out” cables when disconnected from the DVD player.
Plastic Holders
Control Board
(Kit Number H1454 And/Or H6977)
REPLACEMENT INSTRUCTIONS
Figure 1
(Kit Number H1094)
Note: Depending on the type of control board in your fireplace, the
number of steps and components may vary. Following are the types of
control boards for identification:
If you have Kit Number H1094, it will be necessary to replace the board
and IR cables. In this case, complete all the Steps as outlined in these
instructions.
If you have Kit Numbers H1454 or H6977, it is not necessary to replace
the IR cables. In this case, skip Steps 11 through 21 and complete the
remaining process as outlined in these instructions.
Refer to the Reflections Fireplace Installation Instructions manual (No.
850,091M) for a visual aid on the following steps:
Step 1. Disconnect the electrical power to the fireplace.
Step 2. Remove the doors from the fireplace.
Step 3. Remove the reflective glass.
IR Cables
Figure 2
Step 4. Remove the logs.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Step 15. Locate the TV IR cable and cut about five (5) inches from the
end (see Figure 6 ).
Step 16. Twist the connector end of the new IR cable to the ends of the
old IR cable and wrap securely with duct tape. Refer to Figure 7.
Note: Free all cables from one another and pull them individually, as
they are replaced.
Cut Wire Ties If Provided
Pull To Replace
Figure 8
Step 17. Pull the TV IR cable until the new cable is out. Unwrap the tape
and discard the old cable (see Figure 8 ).
Step 18. Locate the Remote Control receiver through the rectangular
slotandpullthecablesoutandcuttheendsfree, enoughtowraptheend
of the new receiver. Then fish them through the rectangular hole while
pulling, to route through the frame cavity (see Figure 9. )
Locate The TV IR Cable
Figure 6
Step 19. Push the Remote Control receiver into the rectangular slot
(refer to Figure 10 ).
Pull Remote Receiver Cables Out
Twist And Tape
Figure 7
Figure 9
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3
Push The Remote Receiver Into The Rectangular Slot
Bundle New Cables And A/V Cables Together With Tape
Figure 10
Step 20. Bundle the new cables and the A/V cables together and wrap
with masking tape, or rout them through the flexible conduit if provided.
See Figures 11 and 12.
Step 21. Tack the wire harness into the side frame and replace the wire
harness shield, if provided (see Figure 13 ).
Figure 12
Tack Wire Harness Behind Side Frame
New Cables Routed
Figure 11
Figure 13
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
4
Step 22. Place the Control Board against the back wall and attach using
the top four (4) outermost holes with the screws and nuts provided.
Refer to Figures 14 and 15.
Step 23. Plug all connectors into the new Control Board.
See Figure 15.
Back Wall With Mounting Holes
Back Wall With Mounting Holes
Figure 14
Power
Heater
Lamp
TV/DVD
Blower
Attach With
Screws Here
Attach With
Screws Here
TV
DVD
Display
Mount The Control Board Using The Screws And Nuts Provided
Figure 15
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
5
DVD INSTALLATION INSTRUCTIONS
Refer to the DVD Replacement Kit Installation Instructions manual (No.
750,250M) for additional aid on the following steps:
Step 1. Before installing the DVD player, connect the new DVD player
to an electrical outlet and insert the DVD disc into the drawer.
Step 2. Disconnect the DVD player and bring it into the fireplace cavity.
Step 3. Proceed to connect the A/V cables as labeled. Connect the
power cord.
Step 4. Place a piece of Velcro on the DVD player eye and attach the IR
transmitter unit to it (see Figure 16 ).
Attach A/V Cables And IR Transmitter Unit
Step5. Withthecontrolsfacingtotherighthandside,tilttheDVDplayer
sideways under the front frame, to insert it into position.
Figure 16
Step 6. Using the new remote control, test the fireplace for proper
operation.
Step 7. Strap the DVD player (see Figure 17 ).
Step 8. Re-assemble the fireplace parts in reverse order.
Strap The DVD Player
Figure 17
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
6
NOTE: THIS PAGE INTENTIONALLY LEFT BLANK.
7
The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by LHP
1110 West Taft Avenue
Orange, CA 92865
P/N 750,251M REV. A 01/2008
|
La Crosse Technology Clock 308 1910 User Manual
LevelOne Network Card PLI 1000 User Manual
Linksys Switch EFAH05W User Manual
Lochinvar Water System INS7141 User Manual
Lucent Technologies Telephone 1079984G3 User Manual
Magnavox VCR VCRVR400BMG User Manual
Makita Cordless Drill 6311D User Manual
Makita Impact Driver 6907DW User Manual
MASS Engineered Design Computer Monitor C4P15 User Manual
Melissa Food Warmer 650 007 User Manual